HDD Broker, Inc. is selling this:

Mincon HDD60

Back

Make: Mincon
Model: HDD60
Category: Construction / Spare Parts, Components and Attachment
Location: North America: United States of America
2575 Northbrooke Plaza Drive Suite 100, 34119, Naples, - USA
Condition: Used
Price: Price on Request

Contact Seller

Description

General Description: Mincon HDD 60 Air Hammer Package with 100 hours only!
Additional Information: SPECIFICATIONS
Hammer Outside Diameter: 4.88" (124 mm)
Pilot Bit Size: 6.25" (159 mm)
Hammer Length: 81.0" (2057 mm)
Hammer Weight: 302 Lbs (137 Kgs)
Piston Weight: 33.6 Lbs (15 Kgs)
Bit Shank Type: HDD60
Backhead Thread 3-1/2" API Reg Pin - Dual steering point design incorporating slanted drill bit and 2° bent sub provides more responsive steering capabilities while transitioning in and out of rock formations.
High frequency hammer cycle transmits less vibration that can be detrimental to sensitive electronics. Rock formations fracture into smaller pieces which are easier to flush out of the bore hole. Less stress transmitted to drill pipe and tool joints. Provides the most effective steering in any pneumatically powered HDD system.
High pressure/high volume compressed air powers drilling operations and requires minimal torque and feed pressure loads on drill machine increasing overall life of drill.
Shorter body design compared to competitive models allows for easier steering in the bore hole and less rotational stresses on hammer body.
Existing locating electronics (DCI, Sub SITE, or WIRELINE) can be used.
Support Station delivers compressed air mixed with a water/polymer (3-5 gal/min) and rock drill oil (2-4 pints/hr) to operate the drilling cycle resulting in minimal environmentally friendly clean up. Can be used on environmentally sensitive locations using biodegradable rock drill oils.
COMPLETE HAMMER: Pneumatic DTH hammer designed with Mincon's proven "High Frequency" piston cycle, 2° Bent sub, Sonde Housing with 3-1/2" API Reg pin connection.
SONDE CARRIAGE: Equipped with sonde locating key and sonde stabilization springs the carriage provides excellent protection to sonde locating device during drilling operations.
(4) x SAFETY WHIP CHECKS: To prevent serious injury due to hose or coupling failure. Whip check connected between the compressor and air hose, air supply hose and support station, support station and air delivery hose, and air delivery hose and drill machine. Install in the fully extended position (no slack) for proper safety assurance.
20' HIGH PRESSURE AIR HOSE: 1000 PSI (68.9 bar) rated air hose with wing nut hammer on couplings.
30' HIGH PRESSURE AIR HOSE: 1000 PSI (68.9 bar) rated air hose with wing nut hammer on couplings.
40' CLEAR WATER SUPPLY HOSE: Connection from water tank to support station with 3/4″ male camlocks at each end.
SUPPORT STATION: Central hub of the system that receives and delivers compressed air to the drill machine, provides lubrication (pneumatic rock drill oil) to the HDD hammer and delivers water/polymer to aid in hole cleaning and stabilization.
TRILITE VALVE CONTROLLER WITH CONNECTIONS: One Touch OPEN-CLOSED or Manual Valve Regulation of compressed air entering Support Station.
(2) x HDD50 SLANT DRILL BIT: Robust 55° face slant for steering, top quality heat treated steel and premium tungsten carbide buttons and wear pads to provide excellent performance and longevity.
SONDE ALIGNMENT TOOL: Aligns the sonde carriage into the 6 O clock position with the bent sub locating pin.
SONDE TORQUE WRENCH: Ensures both ends of the sonde carriage are torqued down to protect the sonde device from damage.
(4) x AIR COUPLERS: Hose couplers to connect compressor, support station and drill machine together. 2 x Female Spud (NPT female x wing nut male) and 2 x Male Spud (NPT male x wing nut male).
-- For more information, visit our website and enter reference #16124
Hours : 100