Strickland Equipment Co. is selling this:

CMI PVM10X

Make
CMI
Model
PVM10X
Category
Construction / Road Construction / Asphalt Machines / Asphalt Paver
Year
1992
Location
North America: United States of America
6902 Spanky Branch Dr., TX 75248-1, Dallas, - USA
Condition
Used
Price
Price on Request

Description

  • SUMMARY:
  • This plant is a CMI model PVM 10EMS SN# 102, built in the Early 90’s and is rated at 350-450 TPH. This CMI Parallel Flow Drum plant is a portable drum mixer plant. The plant is complete MINUS MAJOR POWER CABLES.
  • 8 BIN COLD FEED SYSTEM:
  • (Model # PAB 432 SN# 186) (Model # PAB 432 SN# 187) There are two (2) sets of four portable 10’ X 14’ bins with bin dividers for extra capacity. The 30” feeders are 12’ long and are driven by 5 hp AC Lincoln TEFC motors. The 36” collector conveyor is 86’ long, powered by a 15 hp motor and folds up for transportation.
  • PUGMILL SYSTEM:
  • (Model PMS 303550 SN# 106) the virgin materials feeds onto the 4’ X 10’ single deck screen. Aggregates then feed onto a 32” wide, heavy channel frame conveyor feeds onto a Pug mill Systems twin shaft pug mill. A 30” x 50’ belt scale conveyor that includes the wind guard and gravity take up channel conveyor moves material to the drum. (No Lime Silo)
  • RECYCLE PACKAGE:
  • (Model PRB L20024 SN #133) the single portable recycle bin with an 8’ X 14’ opening with 5 hp AC, Lincoln TEFC motors power the 30” feeders. The bin has one air cannon mounted on the side then onto a 30” wide by nominal 55’ heavy channel frame belt scale conveyor with gravity take-up and wind guard all mounted on single axle fifth wheel carrier.
  • PARALLEL FLOW DRUM:
  • This CMI (Model PVM-10 EMS S# 102), 44’ long recycle drum is cradle chain driven by a 100 hp motor and a Dodge TXT-10 gearbox. Both ends of the dryer are expanded for better combustion and mixing. The drum sits on a 24” wide flange beam frame and includes the hydraulic legs to grade and steel timber footings. A slinger conveyor that is reversible for calibration introduces materials. The Hauck Starjet is model SJL4580F burning #2 diesel. It is powered by a 100 hp TEFC motor. The drum shell has been relined on the outside with an average thickness of .250. The shell is in poor condition and will need replacing.
  • POLLUTION CONTROL:
  • This CMI (Model RA 318P SN# 102) is a reverse air baghouse has 66 rows of bags; each bag is 6” diameter and 7.5’ long. There is a total of 11,663 square feet of cloth that will effectively filter 65,000 cfm of dust-laden air at a 5.57 to 1 air to cloth ratio. All inlet and outlet duct work with backward inclined fan, 2 X 100 hp motors, damper and stack are included. Three screw augers convey the dust to a summing auger. The dust is then blown back into the drum with a pneumatic blower driven by a 25 hp motor. There is triple axle portability.
  • LIQUID ASPHALT STORAGE:
  • There is two (2) portable, 30,000-gallon indirect fired Heatec A.C. tank’s. Tank 1 is a (Model HT 30P SN# H86-068) 30,000 single compartment tank with metering package and heater. Tank 2 (Model HCB 70, SN 94139) 30,000 gallon split tank 12/18 12,000 Fuel and 18,000 A.C. Each Tank is equipped with a Heatec 1 million btu hot oil heater, fired by #2 diesel mounted on the goose neck. There is a three-inch unloading pump and a 3” metering system mounted on the rear of one tank. All insulated plumbing is included with the plant on the tank with the heater. There is a inline pre-heater included and 12,000 skid mounted fuel tank for burner fuel.
  • SILO SYSTEM:
  • The portable, 95-ton CMI self-erect silo system (SE 195) is in good condition. The 36” x 36” drag slat conveyor is 400+ tph. The twin four inch pitch roller chains use 34” x 7.5” x ¾” slats driven by a 60 hp motor move the materials chain and slat on used two seasons. There are sliding bearings on the sidewalls that allow the slats to move up and over any floor obstructions. The anti-segregation batcher is mounted on the end of the slat conveyor. The hopper holds a nominal 95-ton capacity. There are heavy steel liners in the cone area. Hydraulic legs push the silo into the erected position. Steel timber footings are provided. An air compressor is mounted on the goose neck.
  • CONTROL HOUSE:
  • The portable, nominal 11’ X 15’ single level, all steel control house has double pane tinted windows. CMI Impulse II controls manage the plant. Load out is also included with all printer.
  • ENERGY CENTER:
  • (PEC 2U SN# 01292) The individually bucketed Allen Bradley motor controls are in a separable rear room. The MCC is then located on the same frame as the control house (But is removable) MOST OF THE MAJOR CABLE/WIRE IS MISSING FROM PLANT.
  • Each component is portable and or self-erecting with steel timber cribbing.
  • SerialNumber : 102
  • ForSaleListPrice : 375000
*
Ø
▼

Similar Machines

(Similar models of the same year with comparable operating hours.)